Calculator
Not sure what materials you need?
Click here

1 TIL-TAK Original

TIL-TAK sheet No. 1 is the lowest profile sheet in our series of 6 sheets that can be joined together and can have a continuous slope of up to 7.2 metres.

Sheet No. 1 is the sheet you install against the wall of the house and extends 1.25 metres from the wall.

Read about our 100% watertight guarantee under “read more” NOBB No.: 28851467

269,-
Buy
TIL-TAK plate no. 2 er den nest laveste platen i serien av 6 plater som skjøtes etter hverandre og kan danne et sammenhengende fall på opptil 7,2 meter.
Plate nr 2 viderefører fall fra plate nr 1. Med 2 plater kommer du 2,45 meter ut fra vegg.
Les om vår 100% tett garanti under "les mer" NOBB nr: 28851475
269,-
Buy
TIL-TAK sheet no. 3 is the third sheet in the series of 6 sheets that joins in succession to make a continuous drop up to 7,2 meters.
Sheet no. 3 continues the drop from sheet no. 2. 3 sheets covers 3,65 meters.

Read about our 100% watertight guarantee under “read more” NOBB No.: 28851483
269,-
Buy

TIL-TAK sheet no. 4 is the fourth sheet in the series of 6 sheets that joins in succession to make a continuous drop up to 7,2 meters.
Sheet no. 4 continues the drop from sheet no. 3. 4 sheets covers 4,85 meters.

Read about our 100% watertight guarantee under “read more” NOBB No.:

28851491
284,-
Buy

TIL-TAK sheet no. 5 is the fifht sheet in the series of 6 sheets that joins in succession to make a continuous drop up to 7,2 meters.
Sheet no. 5 continues the drop from sheet no. 4. 5 sheets covers 6,05 meters.

Read about our 100% watertight guarantee under “read more” NOBB No.:

28851509
284,-
Buy

TIL-TAK sheet no. 6 is the last sheet in the series of 6 sheets that joins in succession to make a continuous drop up to 7,2 meters.
Sheet no. 6 continues the drop from sheet no. 5. 6 sheets covers 7,25 meters.

Read about our 100% watertight guarantee under “read more” NOBB No.:

28851640
284,-
Buy

TIL-TAK Original adjustment sheet No. 1, the first in the series of 6 adjustment sheets which together can have a continuous slope of up to 7.2 metres.

The sheets cover joist spaces of CC/30–60 cm. Sheet 1 covers 1.25 metres out from the wall. NOBB No.: 28851541

284,-
Buy

This sheet is mounted at an angle on the joist beside it, and bent/trimmed to the correct width.

All sheets are made with a bend along the rear edge, but no drip edge at the front. On adjustment sheet No. 1, the back edge is bent up. On all other adjustment sheets, the back edge is bent down. NB! These sheets must be sealed with sealing compound in ALL seams, because the sheets are against each other in all seams. When you install the sheeting, you always start with the deepest sheet and to adjust the length you simply overlap the sheets more rather than trimming them.

NB! NEVER use an angle grinder on the sheets. This will damage the corrosion-resistant coating lead to rust. Use tin snips.

Read the installation instructions carefully and follow them to ensure a good seal.

NB! Adjustment sheets can only be used in one joist space on each side of the terrace. They cannot be used in adjacent joist spaces or in the middle of a terrace.



NOBB nr: 28851566
284,-
Buy

This sheet is mounted at an angle on the joist beside it, and bent/trimmed to the correct width.

All sheets are made with a bend along the rear edge, but no drip edge at the front. On adjustment sheet No. 1, the back edge is bent up. On all other adjustment sheets, the back edge is bent down. NB! These sheets must be sealed with sealing compound in ALL seams, because the sheets are against each other in all seams. When you install the sheeting, you always start with the deepest sheet and to adjust the length you simply overlap the sheets more rather than trimming them.

NB! NEVER use an angle grinder on the sheets. This will damage the corrosion-resistant coating lead to rust. Use tin snips.

Read the installation instructions carefully and follow them to ensure a good seal.

NB! Adjustment sheets can only be used in one joist space on each side of the terrace. They cannot be used in adjacent joist spaces or in the middle of a terrace.



NOBB nr: 28851574
284,-
Buy

This sheet is mounted at an angle on the joist beside it, and bent/trimmed to the correct width.

All sheets are made with a bend along the rear edge, but no drip edge at the front. On adjustment sheet No. 1, the back edge is bent up. On all other adjustment sheets, the back edge is bent down. NB! These sheets must be sealed with sealing compound in ALL seams, because the sheets are against each other in all seams. When you install the sheeting, you always start with the deepest sheet and to adjust the length you simply overlap the sheets more rather than trimming them.

NB! NEVER use an angle grinder on the sheets. This will damage the corrosion-resistant coating lead to rust. Use tin snips.

Read the installation instructions carefully and follow them to ensure a good seal.

NB! Adjustment sheets can only be used in one joist space on each side of the terrace. They cannot be used in adjacent joist spaces or in the middle of a terrace.


NOBB nr: 28851582
284,-
Buy

This sheet is mounted at an angle on the joist beside it, and bent/trimmed to the correct width.

All sheets are made with a bend along the rear edge, but no drip edge at the front. On adjustment sheet No. 1, the back edge is bent up. On all other adjustment sheets, the back edge is bent down. NB! These sheets must be sealed with sealing compound in ALL seams, because the sheets are against each other in all seams. When you install the sheeting, you always start with the deepest sheet and to adjust the length you simply overlap the sheets more rather than trimming them.

NB! NEVER use an angle grinder on the sheets. This will damage the corrosion-resistant coating lead to rust. Use tin snips.

Read the installation instructions carefully and follow them to ensure a good seal.

NB! Adjustment sheets can only be used in one joist space on each side of the terrace. They cannot be used in adjacent joist spaces or in the middle of a terrace.



NOBB nr: 28851590
284,-
Buy

This sheet is mounted at an angle on the joist beside it, and bent/trimmed to the correct width.

All sheets are made with a bend along the rear edge, but no drip edge at the front. On adjustment sheet No. 1, the back edge is bent up. On all other adjustment sheets, the back edge is bent down. NB! These sheets must be sealed with sealing compound in ALL seams, because the sheets are against each other in all seams. When you install the sheeting, you always start with the deepest sheet and to adjust the length you simply overlap the sheets more rather than trimming them.

NB! NEVER use an angle grinder on the sheets. This will damage the corrosion-resistant coating lead to rust. Use tin snips.

Read the installation instructions carefully and follow them to ensure a good seal.

NB! Adjustment sheets can only be used in one joist space on each side of the terrace. They cannot be used in adjacent joist spaces or in the middle of a terrace.



NOBB nr:28851657
284,-
Buy

TIL-TAK screws, box of 250 pcs

Self-drilling decking screws in hardened steel. These unique screws can easily drill through 2 mm steel sheeting.

TIL-TAK screws have been designed and adapted to our patented TIL-TAK Original sheeting. If you use other screws, you will need to drill holes in the sheets first.

Our decking screws are plated with EPOC and are C4-certified corrosion resistant.

1 box per 10 sheets

NOBB No.: 28851665

351,-
Buy

TIL-TAK sealing compound

Butyl compound that stays flexible and strong. To guarantee a drip-free solution with TIL-TAK Light, you must use our sealing compound. This compound has been carefully selected for its unique and reliable properties and quality.

Seals, remains flexible, easy to apply and can be painted.

Perfect for flexible sealing of seams between building materials indoors and outdoors:

Constructions, glass works, car bodies, caravans and much more!

You need about 3 tubes per 10 Original sheets and about 2 tubes per 10 metres of Light liner.

NOBB No.: 42099733

159,-
Buy

Self-drilling decking screws in hardened steel. These unique screws can easily drill through 2 mm steel sheeting.

TIL-TAK screws have been designed and adapted to our patented TIL-TAK Original sheeting. If you use other screws, you will need to drill holes in the sheets first.

Our decking screws are plated with EPOC and are C4-certified corrosion resistant.

1 box per 10 sheets

440,-
Buy
 1 2 3  
TIL-TAK AS, NorgePb 737 Strømsø, 3003 Drammen, Telephone: 32 83 03 00 E-mail: post@til-tak.noCall us at 32 83 03 00